Workshop «Shaft alignment and dynamic balancing»
We invite technical specialists to participate in the training course on the topic «Shaft alignment and dynamic balancing» which will take place on 06-07 December, 2018 in Germany (Lubeck). The workshop is arranged for specialists in quality, service engineers, mechanics and power engineers who are responsible for the reliability of machines and industrial equipment.

BALTECH GmbH
Kronsforder Allee 45,
23560 Lübeck
Germany
Tel: +49 (0) 451-370-87-700
E-Mail: info@baltech.biz
 
MainProductsDisposalTrainingArticlesContactsImpressum
Products -- Alignment -- BALTECH FG


Calibration gauges BALTECH FG Series,
set of gauges for clearance measurement

  • BALTECH FG, calibration gauges, measurement gauges
  • BALTECH FG-201, thickness feeler gauge, BALTECH FG-202-2
  • Feeler Gauge, BALTECH FG-81, BALTECH FG-133, measuring tools
  • Set of gauges, gauges for clearance measurement BALTECH FG

The set of calibration gauges (gauge) is made of tampered stainless steel and brass. The measurement gauges BALTECH FG Series are intended to measure clearances in different fields, e.g. in motor-building, for adjustment of valve clearances, radial clearances in bearings and during alignment works (determination of half coupling gaps and «soft foot» type), etc. The set of gauges (gauge) are delivered in size 75, 100, 150, 200, 300, 500, 1000mm. We can also supply you with straps in thickness from 0.01 up to 2.0 mm for gauge making, as well as single measurement gauges upon request (with a holder). The measurement gauges can be cylindrical or taper. Advantages of the measurement gauges (gauge) BALTECH FG:

  • easy to use;
  • high measurement accuracy.

The set of calibration gauges (gauge) are normal gages in the form of calibration shims of a certain thickness. The gauges are used to control clearances between planes or deflected position detectors. The measurement gauges are necessary to measure very small distances (e.g. just thicker than a sheet of paper). The gauge can be flat or V-shaped. The gauge can be produced in the form of set of sheets in different thickness in a single holder. The gauge is used separately or in different combinations. The measurements are conducted based on the principle «is inserted- is not inserted».

The sheets are inserted one by one into a measured clearance till one of the sheets is inserted hardly and the next is not inserted at all. The V-shaped gauge is carefully moved to a clearance till it stops after which a thickness specified on the gauge front surface is recorded.


Technical characteristics- gauges, set of gauges, measurement gauges
Set of standard and long gauges BALTECH FG Series
Set 8 pcs.
0,05-0,5 mm
Set 13 pcs.
0,05-1 mm
Set 20 pcs.
0,05-1 mm
Set 20 pcs.
0,1-2 mm
L, mm
BALTECH FG-81 BALTECH FG-131 BALTECH FG-201 BALTECH FG-201-2 1000
BALTECH FG-82 BALTECH FG-132 BALTECH FG-202 BALTECH FG-202-2 500
BALTECH FG-83 BALTECH FG-133 BALTECH FG-203 BALTECH FG-203-2 300
BALTECH FG-84 BALTECH FG-134 BALTECH FG-204 BALTECH FG-204-2 200
BALTECH FG-85 BALTECH FG-135 BALTECH FG-205 BALTECH FG-205-2 150
BALTECH FG-86 BALTECH FG-136 BALTECH FG-206 BALTECH FG-206-2 (21 pcs.)
BALTECH FG-207-2 (32 pcs.)
100
Set 6 pcs.
0,1-0,4 mm
Set 7 pcs.
0,1-0,5 mm
Set 10 pcs.
0,1-1,0 mm
Set 11 pcs.
0,05-0,8 mm
L, mm 
BALTECH FG-87 BALTECH FG-137 -

-

75

Back      Main